If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Maxim Firearms is Frank. http://www.maximfirearms.com/contact/ He is a machinist and makes bolt's, extractors, carriers and more.
Precision Firearms is Mark. He builds rifles and specializes in Grendels. Not sure if Mark is selling extractors.
We have a few extra in Super Match if you need. Also running some on the CNC tonight and most of Tomorrow. Hoping to get about 200 done. These though will need to go to finishers first so they will be about 2 weeks max. Then we will have plenty. These have no sharp edges and are hand inspected.
Maxim Firearms is Frank. http://www.maximfirearms.com/contact/ He is a machinist and makes bolt's, extractors, carriers and more.
Precision Firearms is Mark. He builds rifles and specializes in Grendels. Not sure if Mark is selling extractors.
Does that mean I am not a machinist? You know I have 2 Mori Seiki Horizontals, 2 Mori Verticals, 3 Mori Lathes and one Hass VF3 Right? We draw in Solid Works. I personally do all the drawings (modeling) and have two guys that do the CAM work, although I can do that too. We are drawing up 308 Upper Receivers right now!
I have 2 Mori Seiki Horizontals, 2 Mori Verticals, 3 Mori Lathes and one Hass VF3 Right? We draw in Solid Works. I personally do all the drawings (modeling) and have two guys that do the CAM work, although I can do that too. We are drawing up 308 Upper Receivers right now!
Does that mean I am not a machinist? You know I have 2 Mori Seiki Horizontals, 2 Mori Verticals, 3 Mori Lathes and one Hass VF3 Right? We draw in Solid Works. I personally do all the drawings (modeling) and have two guys that do the CAM work, although I can do that too. We are drawing up 308 Upper Receivers right now!
Mark Hostetter
Precision Firearms
You know I wasn't meaning it like that.. like we talked, your a rifle manufacture "as you said" not a barrel and parts dealer but looks like your going that way so all the more people making parts the merrier.
And you manufacture some bad ass receiver sets too. And I do like the 308/AR10 lower we looked and and glad your getting the upper going. I guess the new facility is making more room for you to expand so glad things are moving forward....
We already offer the Creedmore with either the Lilja or Bartlein Barrels. I need to get these listed. They are the same price as the 260 Remington uppers on our website with Lilja Barrels, 40 more for Bartlein Barrels.
You know I wasn't meaning it like that.. like we talked, your a rifle manufacture "as you said" not a barrel and parts dealer but looks like your going that way so all the more people making parts the merrier.
And you manufacture some bad ass receiver sets too. And I do like the 308/AR10 lower we looked and and glad your getting the upper going. I guess the new facility is making more room for you to expand so glad things are moving forward....
Does that mean I am not a machinist? You know I have 2 Mori Seiki Horizontals, 2 Mori Verticals, 3 Mori Lathes and one Hass VF3 Right? We draw in Solid Works. I personally do all the drawings (modeling) and have two guys that do the CAM work, although I can do that too. We are drawing up 308 Upper Receivers right now!
Not sure yet. I think it was a poor move on DPMS parts to change the 308 pattern again. Not convinced the system is quite strong enough for match grade 308's either.
Comment