Monster 20" build - Printable Version

Monster 20" build - Printable Version

+- 6.5 Grendel Forum (https://65grendel.com)
+-- Forum: 6.5 GRENDEL DISCUSSION FORUMS (https://65grendel.com/forumdisplay.php?fid=3)
+--- Forum: 6.5 Grendel Photo Gallery (https://65grendel.com/forumdisplay.php?fid=16)
+--- Thread: Monster 20" build (/showthread.php?tid=17775)

Monster 20" build - Mark6.5 - 12-19-2018

Here is my build with the Monster 20 group buy barrel. It replaced a BCA SS 5R 20" that shot pretty darn good after i did some hand lapping of the bore and crown. This monster on my first 15 shots at 85 yards shot .55" with 6 shot group with factory black ammo. I am more than happy. It going to be a beast after the new year when i start to develop loads for it. Can't wait to get out to the range so i can get her zeroed at 100 yards. The 85 yard test shots was out near my mom's house.

This was a semi budget build. I could have chosen some more affordable parts than some of the ones i used, but the parts i put a bit of money in where the ones i felt matter the most. The barrel from BFT group buy is a amazing value! Would love to see a 22" from them.

She was built mainly to shoot out to 600-1000 yards at paper and steel, but she is now light enough to hunt with if i don't want to carry the weight of my 450BM

Parts List:

Monster 20 20" 5REE barrel

KM Tactical smooth side upper

17" slim M-Lok Handguard ( don't remember where purchased, i've had it for a while)

Atheris Rifle Co. 6.5 Grendel BCG

Atheris Rifle Co. Lower

Velocity Trigger's 3lb Straight Trigger

Anarchy Outdoors' "Penguin Grip" Precision Rifle Grip

Strike Industries Enhanced Castle Nut & Extended End Plate

Strike Industries Mono Pod

MidTen Tactical M-LOK Bipod 7.5-9 Inches

Generic ambidextrous charging handle

JE Designs Ar-15 "Quiet" Recoil Captured Spring & Buffer System

Heluis Tactical Stainless Seventeen SeventySix muzzle device.

UTG Accu-Sync 30 Rings

Scope is 4-16x44 FFP prototype.

Ambidextrous magazine release

Ambidextrous safety selector

Xtreme Precision extended takedown pins

Xtreme Precision anti roll pins

Xtreme Precision spring kit

Prototype Adjustable gas block

Pistol buffer tube

XLR knock off buttstock

Monster 20" build - Mark6.5 - 12-19-2018

Few more pics

Monster 20" build - A5BLASTER - 12-19-2018

Looks good sir. The 20 inch I have is a great shooter, going to make a great training and hunt gun for its new owner.

Monster 20" build - Swampfox - 12-24-2018

That is bad ass looking AR. Does the stock adjust in and out?

Monster 20" build - RMiller - 12-24-2018

Nice!

Monster 20" build - Mark6.5 - 12-24-2018

Swampfox Wrote:That is bad ass looking AR. Does the stock adjust in and out?

Thank you. It was the first Battle Scared theme i've done. Yes the stock is adjustable in and out.

Monster 20" build - Mark6.5 - 12-24-2018

RMiller Wrote:Nice!

Thank you

Monster 20" build - Dscoduc - 12-24-2018

Did you scrape off the coating on the barrel and other components? If so, was there any particular reason why?

Monster 20" build - Mark6.5 - 12-24-2018

Dscoduc Wrote:Did you scrape off the coating on the barrel and other components? If so, was there any particular reason why?

Not on the barrel. It was just coated over than 120 grit sand was done to that coating. But on the other parts more sanding done to get done to some bare metal in spots than a light coat of peral was applied. The reason is look called battle scared. Just make parts look used or like that have taken a beaten. I also like the looks the technique.

Monster 20" build - Mark6.5 - 12-27-2018

Just little update finally made my stencils. Added a little Horde pride. The symbols on the upper receiver i sprayed pearl white in the stencil and the ones on the mags i put the stencils on than removed the paint from in side the stencils and than polished it a little.

Monster 20" build - bj139 - 12-27-2018

Nice artwork. Were the parts coated with aluminum paint?

Monster 20" build - Mark6.5 - 12-27-2018

bj139 Wrote:Nice artwork. Were the parts coated with aluminum paint?

Thank you. All the paint used is a high temp automotive paint i bought from local automotive paint supplier.