This is the result of (1) lapping the receiver, (2) bedding with Loctite 620, and (3) polishing the feed ramps. 5 shots at 100 yards. I'll take it.
Accuracy fixed.
Collapse
X
-
Originally posted by just_john View PostKlem, there is no issue with a little loctite on the face of the receiver. The point of lapping and loctiting is to facilitate a "single piece of metal" barrel thru receiver. If there is a little loctite on the face ( after cleaning off the excess), when the barrel nut is torqued down, it just helps to insure that there is no slack anywhere between the barrel and receiver. If there is any space or gap anywhere in this transitional area, there is opportunity for movement at ignition which creates an upredictable shot to shot variation. Just remember that if a little loctite is a good thing, a lot of it isn't!
I am aware quite a few people don't care about the excess glue squeezing onto the shoulder but I imagine your guns would be even more accurate if you could somehow get the glue to where it is needed, and keep it from where it is not.
Comment
-
-
Originally posted by Klem View PostI am aware quite a few people don't care about the excess glue squeezing onto the shoulder but I imagine your guns would be even more accurate if you could somehow get the glue to where it is needed, and keep it from where it is not.
Comment
-
-
Originally posted by dreadpirate View PostEasy - heat the barrel nut with a torch so the Loctite flows out and settles in the gaps after you have it assembled. Use Loctite 620 which should not liquefy under normal shooting temperatures.
Why don't you coat the inside of the receiver with glue and not the outside of the barrel extension? Then as the two parts are brought together it pushes the excess in the opposite direction of the face. Hopefully the receiver face and shoulder remains clean. It would be a little more fiddly cleaning the excess but there's enough access into the receiver to do this.
Screw the barrel nut on and leave it vertical with the barrel pointing down. Gravity keeps the liquid glue right up to but not on the face as it hardens.Last edited by Klem; 07-15-2017, 07:54 AM.
Comment
-
-
Originally posted by Klem View PostHeat it with a torch? To be clear, you mean a naked flame? No, heating aluminum brings with it the potential of annealing. There has to be a better way.
[EDIT] At what temp for annealing aluminum? 800 deg F? Don't think I got it that hot.Last edited by dreadpirate; 07-15-2017, 02:22 PM.
Comment
-
-
Originally posted by dreadpirate View PostHave to be careful yes. I heated the barrel bolt and did not torch the aluminum upper directly.
[EDIT] At what temp for annealing aluminum? 800 deg F? Don't think I got it that hot.
That said, your glue will be flowing/liquid as you apply it and before hardening anyway... so why heat it?
I hear what you are saying, implying it is not a big deal, but I think it is. Heating the receiver and barrel nut with a naked flame hoping the metal properties remain the same is wishful thinking. Applying glue to the interface between the receiver face and barrel extension journal does not make sense to me. Applying glue however to fill any tiny void between the barrel extension and receiver (evidenced by slop) does make sense, perfect sense in fact.
I suppose it also depends on the quality of parts you end up with, and are prepared to tolerate. Top quality 7075 billet receivers by companies like Mega Arms will never need glue (or you return them for a replacement/refund). Lower end, non-MILSPEC forged 6061 receivers are more likely to be out of spec. But then, they are also cheap so can be replaced, instead of trying to fix sloppy tolerances with glue...Just saying.
I know I'm playing Devil's Advocate here and wish you well with your builds. I guess I need to work through all the reasons for doing this in my own mind. A beautiful group by the way - excellent shooting.Last edited by Klem; 07-15-2017, 05:17 PM.
Comment
-
-
I would think that if one did want to apply Loctite inside the receiver first and then install the barrel extension, screwing the barrel nut on to the proper torque specs and leaving it vertical with the barrel pointing down would let gravity do its thing. Keeping the liquid glue right up to, but not on the face as it hardens would be easy and smart as well.
Comment
-
-
Originally posted by Klem View PostThanks for replying but I remain unconvinced that glue between the receiver face and barrel extension increases accuracy. If you go to the effort of shaving minute angles of metal off the receiver face to square it why then let glue or any other substance in between that carefully machined interface? If there is slop between the extension and receiver then by all means try and fill it with something that hardens (and does not flow when heated). But the receiver face and the extension journal needs to be intimate.
I am aware quite a few people don't care about the excess glue squeezing onto the shoulder but I imagine your guns would be even more accurate if you could somehow get the glue to where it is needed, and keep it from where it is not.
Comment
-
-
I would hope that the barrel receiver extension would be true, not require lapping.
Lapping a receiver however has been proven again and again that it is a benefit.
Bedding the barrel extension into the receiver by whatever means has also proven to be a benifit - though I agree with Klem that any bedding material that requires heat should be avoided. Heat and slow cool on Aluminum and Aluminum alloys makes them harder - pushing brittle depending on the original properties and how much heat was applied.
I'd stick with the tried and true blue locktite applied in a thin layer in both the receiver and on the barrel extension, taking care to not push excess into the internals of the receiver, and keeping it off the threads. Install the barrel nut with aluminum or nickel antisieze (prevent dissimilar metal electrolysis), torque to spec and clock if needed for gas tube, let sit for 24 hours until cured.Sticks
Catchy sig line here.
Comment
-
-
Klem et al - fair enough; perhaps the heat treatment is not worth the side effects. The armorer I was working with seemed to think it would "set" the Loctite 620 in place. Heating or not; I still think the bedding and lapping are worth it. My question is should this ALWAYS be done when assembling an upper, or or only done if you are having accuracy issues? The reason I started done this road is (1) this was my first upper assembly and I wanted a pro to double check my work, and (2) the rifle was shooting 2" groups at 100 yards.
Comment
-
-
Here's another thing to think about; even if you don't apply heat to the Loctite initially. If you want to change the barrel, you will have to heat the Loctite to, what?, like 400 deg F to get it loose? Guess it depends on which Loctite you use. But you MUST use a Loctite that will not melt during normal shooting. My point is; once you go down the path of Loctite, you will have to apply heat at some point in the future to remove the barrel, right?
Comment
-
-
Here's what Loctite says:
"TYPICAL CURING PERFORMANCE
Product 3620 has been specifically developed to cure at lower
temperatures and/or shorter times than standard products.
Rate of cure
and final strength will depend on the residence time at the cure
temperature."
So you are supposed to heat it to 220 deg F, not 400 deg F. Hopefully that's what I did
Comment
-
-
So now I'm curious, what temp does the barrel extension and chamber heat up to with an ambient temp of 95* shooting 10 shots at lets say in 20 seconds produce? Or, how many shots can be fired before the temp gets high enough to start to melt the blue loctite?
Comment
-
Comment